Sand the turning to at least 400-600 grit. As the turning revolves on the lathe, hold the bar of HUT™ to one end and move it slowly to the other en...

Sand the turning to at least 400-600 grit. As the turning revolves on the lathe, hold the bar of HUT™ to one end and move it slowly to the other en...

 Wood buffing wheels are similar to the metal buffing versions, but softer and looser, to conform to the contours of the work without blurring the ...

 Treen Mandrel Starter Kit + #2 Morse Taper (Mandrels & Gauge Ring, three Lid Insert/Stopper Sets, Cork Sheet, & Instructions plus a #2 Mor...

 This sharp-edged 1" driver for the smaller lid mandrel is designed to turn hollow lids or stoppers - especially those used for salt and pepper sha...

This bar is designed to be used with the Beall Tripoli buffing wheel. It is the first step in a 3 step process that also includes: The White Diamon...

Finally - a device that allows you to run three buffs simultaneously. On one end of this 17" mandrel is machined a #2 Morse taper to fit in the he...

We have had many requests from turners for a longer buffing mandrel which would give them better access to the insides of deep bowls. In response, ...

This bar of Carnauba wax to be used on the carnauba buffing wheel. A thin coat of Carnauba wax -a non toxic-edible substance. Thus making this a pa...

 We have had many requests from turners for a longer buffing mandrel which would give them better access to the insides of deep bowls. In response,...

Wood buffing has been used by pipemakers to polish their briars for years. We first became intrigued by the process when we saw the impressive resu...

Wood buffing has been used by pipemakers to polish their briars for years. We first became intrigued by the process when we saw the impressive resu...

 Carnauba Wax not included

Wood buffing has been used by pipemakers to polish their briars for years. We first became intrigued by the process when we saw the impressive resu...

The purpose of Bowl Buffs and other similarly shaped products is the same — to buff concave surfaces thoroughly and safely. Unlike those "others" ...

 Finally - a device that allows you to run three buffs simultaneously. On one end of this 17" mandrel is machined a #2 Morse taper to fit in the he...

The purpose of Bowl Buffs and other similarly shaped products is the same — to buff concave surfaces thoroughly and safely. Unlike those "others" ...

The purpose of Bowl Buffs and other similarly shaped products is the same — to buff concave surfaces thoroughly and safely. Unlike those "others" h...

If you prefer to do your buffing on the lathe, and your lathe takes a #1 or #2 Morse taper, these attachments will allow you to mount your buffs se...

These taps are machined in lathe spindle sizes so that after you have drilled a wood block, you can tap it and mount it directly on your lathe. The...

This is what you need to fix those bent or out of round mandrel. Fits Precision Mandrel 

 #1 Morse Taper Maxi-Mandrel - This new mandrel features a 7mm mandrel shaft that slides through a headstock collet. This feature guarantees a perf...

Thread on 3/4" x 16tpi screw on for Sears, Carba-tec, Ryobi and Record lathes. Includes long mandrel, knurled nut, seven 7mm bushings, 7mm drill bi...

Slip-on 5/8" diameter (no thread) for Shopsmith lathes. Includes long mandrel, knurled nut, seven 7mm bushings, 7mm drill bit. Compatible with all ...

Product Description Now you can disassemble and assemble your pen parts all on one easy to use tool. Acts as a traditional pen press to reliably an...

Drill Center Vise   Pen Blank Drilling Center ViseDrill through the exact center of your pen blanks The jaws on the drilling center move in and o...

Product Description Numerous turning projects require a jam chuck however hand turning the chuck is time consuming and not always accurate. This ...